Diagnosys Pinpoint II P2R-14 14-Slot PCB Test Reverse Engineering System TestVue

Description

Diagnosys Pinpoint II P2R-14 14-Slot PCB Test Reverse Engineering System TestVue
Software Rev: 3.31.15.1704
Program Studio
Test Board
Device Test
Installed Boards (as pictured)
Matrix
Scanner
2x Driver Boards
Analog
VTC
Controller
In Software modules:
Analog Card With DMM, LCR Meter, Timer / Counter, Waveform Generator, Oscilloscope, And Analog Inputs
"Diagnoysis Pinpoint II Circuit board test & diagnostic system
Multi-strategy testing for confidence
Test of Individual Components and Edge connectors testing
The PinPoint system performs tests on individual components using in-circuit test methods and a fixtureless clip technique. These dynamic digital and analog tests prove the correct operation of each device and can also detect opens, shorts, voltage, digital failures and incorrect, broken or missing passive components on networks. These tests can also be applied at the edge connector of a circuit to prove the functionality of the whole circuit.
Powerful V/I testing
In addition to the advanced and powerful digital tests, the PinPoint system also utilises a V/I testing technique. This technique applies a sinusoidal signal to a network and learns the four quadrant signature for it. This signature is then stored and used for comparison of the network on other boards giving an instant indication of any error. The results are graphically displayed on the screen. This power-off technique can be applied to any board and is therefore ideal when little or no information is available about the device or networks being tested.
Parametric Test Unit (PTU)
Four discrete channels on the PinPoint Vectorless Test card are dedicated to DC voltage and current sources. These channels can be used for functional testing of discrete components both in and out of circuit, for example: hFE of transistors or semiconductor junction forward voltage.
LCR Bridge
The LCR bridge is used to measure the values of Inductors, Capacitors and Resistors in or out of circuit. Powered by TestVue software you immediately feel in control of the straight-forward tool and can put it to use immediately testing components. Measuring the values of a network impedance is now a straight forward task that enhances the diagnostic capabilities available in the PinPoint system.
Control PXI and GPIB instrumentation
Extending the capability of the PinPoint system even further is its inherent capability to control PXI and GPIB instrumentation. Having PXI control of these instruments through the user friendly TestVue™ software allows you to create functional analog tests for your circuits. Instrument Strategizer gives the graphic capability to program and sequence instruments with other code to provide a seamless mixed signal test program. Additional power supplies can also be added to enhance the standard system UUT (Unit Under Test) power supplies for extended test capabilities.
Reverse Engineering
Another key capability of the PinPoint is the ability to reverse engineer to a Schematic Diagram or Netlist from an unknown circuit. This provides you with the ability to test, diagnose and repair circuits that have been declared obsolete by the OEM (Original Equipment Manufacturer) and give you protection from obsolescence.
Boundary Scan
This technique can be applied to a single device or a chain of devices that are enabled with the necessary hardware. Adding to the capability of test methods available, the integration of your preferred Boundary Scan solution provides you with the ability to create a flexible and comprehensive test of your circuits.
TrakTest
This facility tests the continuity of tracks between devices and also tests for the presence of short circuits between pins of a device. Through reference to a netlist for the circuit, the PinPoint rapidly detects incorrect open and short circuits in the circuit. If the netlist is not readily available then the PinPoint can be used to generate one from a known good board using its’ Reverse Engineering facility.
Shorts Locator
The Shorts Locator provides an interactive tool that enables you to determine the exact point at which a short circuit has occurred in the circuit being tested. The graphical interface provides an intuitive display of all the relevant data necessary to allow you to easily and accurately define the exact point of the failure.
Back Driving
In-circuit testing requires signals to be forced into a circuit often backdriving voltages onto the output of a connected device. To ensure effective testing the PinPoint has a market leading capability to deliver 750mA or more of back driving current on each channel as required giving it excellent backdriving performance and signal quality. Essential for safe testing of a circuit the PinPoint fully complies with the internationally recognised UK Defence Standard.
Overview:
Passive in-circuit
Dynamic digital in-circuit
Functional Analog in-circuit
Boundary Scan in-circuit
Boundary Scan connector
Advanced Nodal Signatures
Functional Analog edge connector
Dynamic digital edge connector
Cluster Test
Analog functional with external instruments"
-As Described by manufacturer
This unit is onsite, is setup and we welcome for you to come inspect this unit.
Please email if you have any questions or would like to speak with someone in person. Call Bullseye Calibration in Bloomfield, CT to discuss the machine or payment options.
SHIPPING POLICY:
We sell sensitive test and measurement equipment here on Ebay.  We strive for 5-star service, so we invest a great deal of time and care to package all of our items safely for shipment.  This attention to detail means it may take up to 10 days for us to prepare and ship your units out of our facility. We want to support you throughout the transaction and want you to be satisfied, so please to contact us at Bullseye Calibration in Bloomfield, CT with any questions or concerns.  We do out best to ship quickly, but never at the expense of quality delivery.
RETURN POLICY:
All units are being sold "WITH A 30 DAY RIGHT OF RETURN". The auction description is written as a guide, we strongly recommend that you come view and test the units at our facility. Feel free to give us a call at Bullseye Calibration in Bloomfield, CT, and we will help answer any questions that you may have, before you purchase an item. We do not accept returns so please call with any questions that you have BEFORE you bid.